Transactions of the American Society of Mechanical Engineers, Volume 45American Society of Mechanical Engineers., 1924 Vols. 2, 4-11, 62-68 include the Society's Membership list; v. 55-80 include the Journal of applied mechanics (also issued separately) as contributions from the Society's Applied Mechanics Division. |
From inside the book
Results 1-5 of 57
Page
... Milling Cutters on Power Requirements and Capacity .. 165 1897 FRED A. PARSONS , Power Required for Cutting Metal .. 1898 C. J. JEFFERSON , The Efficiency of the Scotch Marine Boiler .. 193 229 1899 H. E. DOOLITTLE , The Integrating ...
... Milling Cutters on Power Requirements and Capacity .. 165 1897 FRED A. PARSONS , Power Required for Cutting Metal .. 1898 C. J. JEFFERSON , The Efficiency of the Scotch Marine Boiler .. 193 229 1899 H. E. DOOLITTLE , The Integrating ...
Page 164
... these can be fully manned without interference or congestion , which will have an important bearing on production costs . No. 1896 EFFECT OF VARIATIONS IN DESIGN OF MILLING CUTTERS 164 STEEL - CAR CONSTRUCTION , C. P. RY .
... these can be fully manned without interference or congestion , which will have an important bearing on production costs . No. 1896 EFFECT OF VARIATIONS IN DESIGN OF MILLING CUTTERS 164 STEEL - CAR CONSTRUCTION , C. P. RY .
Page 165
... Engineers , Philadelphia , February 27. 1923. Abridged . rake angle , and cutting speed of the cutter on 165 BENJAMIN P GRAVES and JAMES A HALL, Effect Variations in Design of Milling Cutters on Power Requirements and Capacity.
... Engineers , Philadelphia , February 27. 1923. Abridged . rake angle , and cutting speed of the cutter on 165 BENJAMIN P GRAVES and JAMES A HALL, Effect Variations in Design of Milling Cutters on Power Requirements and Capacity.
Page 166
... limits the efficiency of the drive to a reasonable margin of safety below 50 per cent when operating on a high - speed return , and to a much lower figure at cutting speeds . 166 EFFECT OF VARIATIONS IN DESIGN OF MILLING CUTTERS.
... limits the efficiency of the drive to a reasonable margin of safety below 50 per cent when operating on a high - speed return , and to a much lower figure at cutting speeds . 166 EFFECT OF VARIATIONS IN DESIGN OF MILLING CUTTERS.
Page 167
... CUTTERS 8 High - speed - steel cutters 31⁄2 in . in diameter were used in all of the tests , excepting a few tests with two 6 - in . side milling cutters . All of the 32 - in . cutters used in the tests to determine the effect of the ...
... CUTTERS 8 High - speed - steel cutters 31⁄2 in . in diameter were used in all of the tests , excepting a few tests with two 6 - in . side milling cutters . All of the 32 - in . cutters used in the tests to determine the effect of the ...
Contents
1 | |
4 | |
9 | |
13 | |
21 | |
41 | |
67 | |
77 | |
271 | |
285 | |
343 | |
393 | |
405 | |
471 | |
472 | |
497 | |
99 | |
111 | |
135 | |
141 | |
151 | |
165 | |
193 | |
239 | |
257 | |
527 | |
607 | |
786 | |
825 | |
841 | |
884 | |
889 | |
931 | |
Other editions - View all
Common terms and phrases
accuracy accurate angle apparatus average axis balancing machine boiler cars cent Center of area coal coefficient combustion computed cost curves depth of cut determined diagram diameter discharge efficiency electrical electrodes factor feed fine-tooth cutter flow formula friction fuel fulcrum gage Gibson head heat horsepower hydraulic hydroelectric impulse wheels increased installation insulation kilowatt lathe tools Laurentide lignite load loss maximum MECHANICAL ENGINEERS milling cutters milling machines Niagara number of teeth obtained operation output paper penstock piezometer pipe plant plates Pop valve power required practice preheater pressure rake angle record refrigerator cars salt velocity method sec-ft shown in Fig shows slide rule Society Station steam steel superheater surface Table tank temperature tests tion tool tooth true Q tube turbine unit venturi meter vertical vibrating vibrating bed watt-hour meter wattmeter weir
Popular passages
Page 284 - Profession by exchanging general information and experience with his fellow engineers and students of engineering and also by contributing to work of engineering societies, schools of applied science and the technical press. 10 He will interest himself in the public welfare in behalf of which he will be ready to apply his special knowledge, skill and training for the use and benefit of mankind.
Page 182 - Slide rules for the machine shop, as a part of the Taylor system of management
Page 280 - Society are to promote the art and science of mechanical engineering and the allied arts and sciences ; to encourage original research ; to foster engineering education ; to advance the standards of engineering ; to promote the intercourse of engineers among themselves and with allied technologists ; and severally and in cooperation with other engineering and technical societies to broaden the usefulness of the engineering profession.
Page 282 - ... invested, the amount and nature of the property acquired during the year immediately preceding the date of the report and the manner of the acquisition; the amount applied, appropriated or expended during the year immediately preceding such date, and the purposes, objects or persons to or for which such applications, appropriations or expenditures have been made...
Page 914 - Engineers, the American Society of Naval Architects and Marine Engineers, the Society for the Promotion of Engineering Education, and the Boston Society of Civil Engineers. His publications include "The Frigate Constitution," and various scientific papers.
Page 284 - Engineering work has become an increasingly important factor in the progress of civilization and in the welfare of the community. The engineering profession is held responsible for the planning, construction and operation of such work and is entitled to the position and authority which will enable it to discharge this responsibility and to render effective service to humanity. That the dignity of their chosen profession may be maintained, it is the duty of all engineers to conduct themselves according...
Page 904 - At the beginning of the civil war he enlisted as a private in the First Minnesota regiment, but was commissioned by Governor Ramsey its lieutenant colonel.
Page 281 - Junior must have had such engineering experience as will enable him to fill a subordinate position in engineering work, or he must be a graduate of an engineering school of accepted standing. He must be at least twenty-one (21) years of age, and his connection with the Society shall cease when he becomes thirty (30) years of age unless he be previously transferred to another grade.
Page 828 - Again quoting Professor Roe: There is a great difference between judgment and measurement. To judge is to arrive at a conclusion or decision by weighing or comparing. To measure is to ascertain quality, dimensions, or quantity by comparison with a standard. In judging things they are compared one with another. In measuring them all are compared with the same thing, namely; the standard. Comparison is common to both, but the use of an agreed-upon standard as the basis of comparison distinguishes measurement...
Page 882 - Sumner Line of Position, furnished ready to lay down upon the chart by means of tables of simultaneous hour angle and azimuth of celestial bodies of declination ranging from 27° N. to 27° S. of the celestial equator...